Skip to main content

[MW:858] 857] Diffusible H2 content and Hydrogen cracking study

By Materials & Welding
Dear Mr.Ragu,

Thanks for warning me. I just forget that Codes & standards should not be
copied in any form.

Thanks once again.

Regards,

S.Mathusoothanan

-----Original Message-----
From: materials-welding@googlegroups.com
[mailto:materials-welding@googlegroups.com] On Behalf Of Bathula Raghuram
(Mumbai - PIPING)
Sent: 12 June, 2008 8:01 AM
To: materials-welding@googlegroups.com
Subject: [MW:857] Diffusible H2 content and Hydrogen cracking study


Dear Mr Mathusoothanan

Apriciate your posting, but I have to approve this message without the
attchements, since it is agianst the rules of this group (and all
members are requested to not post any codes/standards as attachements
in the group)

Thanking you for your co operation!

-----Original Message-----
From: mathu.subramanian [mailto:mathu.subramanian@kharafinational.com]
Sent: Thursday, June 12, 2008 10:20 AM
To: materials-welding@googlegroups.com
Subject: 851] Diffusible H2 content and Hydrogen cracking study

Dear friend,

E6013 is not the compatible electrode to weld Cr-Mo steels and it is
normal
carbon steel electrode. In Cr-Mo steels so many grades are there. Gr.1,
Gr.11, Gr.22, Gr.5, Gr.9, Gr.91. Please refer attached ASME Specs for
Electrodes & Materials. According to grade of material welding
electrodes is
to be selected.

As said by Mr Raghuram, two different AWS classifications can not be
compared for
diffusible hydrogen level. Two hydrogen levels of same AWS
classification
should be selcted.

I think the material grade you have selected might be Grade 9.

Regards.

S.Mathusoothanan

-----Original Message-----
From: materials-welding@googlegroups.com
[mailto:materials-welding@googlegroups.com] On Behalf Of Bathula
Raghuram
(Mumbai - PIPING)
Sent: 12 June, 2008 6:31 AM
To: materials-welding@googlegroups.com
Subject: [MW:851] Diffusible H2 content and Hydrogen cracking study


What type of Cr-Mo steel it is?
What is the basis of selecting E6013 for Cr-Mo steel?
Why diffusion hydrogen level required for E6013, when it is not a low
hydrogen electrode?
One can't compare the stress value with two different AWS
classifications; instead you can study by taking two different batches
of E9015B9 electrodes with different diff H2 levels (not comparing with
E6013) and test it!

Members please share your thoughts

-----Original Message-----
From: materials-welding@googlegroups.com
[mailto:materials-welding@googlegroups.com] On Behalf Of mech
Sent: Wednesday, June 11, 2008 7:49 PM
To: Materials & Welding
Subject: [MW:846] on preheating effect


dear sir
i am a welding engg student and doing project on hydrogen cracking
of cr-mo steel by using implant test method.
the following result were observed

electrode diff hydrogen
level critical stress

E6013 (ruttile type) 5
ml 456 mpa
E9015 B9
10.6ml 500 mpa
according to theory if hydrogen level increases critical cracking
stress will decreases but in my exp critical cracking stress is coming
more in low level of hydrogen

i would like to have your comment on this result

--~--~---------~--~----~------------~-------~--~----~
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
-~----------~----~----~----~------~----~------~--~---

Comments

Post a Comment

Popular posts from this blog

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

The Schaeffler and Delong diagrams for predicting ferrite levels in austenitic stainless steel welds

By Materials & Welding
Introduction Ferrite is important in avoiding hot cracking in during cooling from welding of austenitic stainless steels. 'Constitution diagrams' are used to predict ferrite levels from the composition by comparing the effects of austenite and ferrite stabilising elements. The Schaeffler and Delong diagrams are the original methods of predicting the phase balances in austenitic stainless steel welds. Nickel and chromium equivalents A 'nickel equivalent' is calculated for the austenite stabilising elements and a 'chromium equivalent' ferrite stabilising elements. These are used as the axes for the diagrams, which show the compositional equivalent areas where the phases austenite, ferrite, martensite (and mixtures of these) should be present. Although intended to show the phase balance of weld fillers, these diagrams can also be used to illustrate the phase balance of the 'parent' material. There are different diagrams for dif...
Post a Comment
Read more