Skip to main content

Re: [MW:32420] Solid Tube Built up WPS/PQR

By Materials & Welding
Mr.Jaimin Patel,
fyi,
build‐up of base metal (restoration of base metal thickness):
This is the application of a weld material to a base
metal so as to restore the design thickness and/or structural
integrity. This build‐up may be with a chemistry different
from the base metal chemistry which has been
qualified via a standard butt-welded test coupon. Also,
may be called base metal repair or buildup.


On Mon, May 10, 2021 at 6:46 AM jaimin...@gmail.com <jaiminthejack@gmail.com> wrote:
Dear Gents,

we have situation where client have some component like shaft/Tube Solid  of nickel Grade Material and on the surface they have some material loss.

They want to make grinding>welding>maching to restore the original configuration.

  1. Applicable Code ASME SEC. IX.
  2. Required welding max 5mm.
  3. Shaft Dia varies From 1" to 6"
  • Now as i see we can make WPS/PQR based on QW202.3.
  • But I m confused on selection of Base metal thickness and Grove what we need to suggest.
  • Client don't have metal sheets to make on PQR on that they have only Solid Tubes.

kindly give your value inputs on this regard's.
Thanks & Regards
Jaimin Patel
B.E Mechanical
ASNT NDT L-III(222210)
Email : jaiminthejack@gmail.com 
Skype : jaimin0011
WHATSAPP : +919099018587
 
Failure is simply the opportunity to begin again, this time more intelligently. Henry Ford

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/99a50403-988c-4b59-b32d-e8c24d4c8524n%40googlegroups.com.


--
With Regards

Udaya bahaskar.D

+919676270121

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CANii3RM%3DG6GMAYP71ftL5OMzBMVOL%3DwAVDoUOJ0yv%2BUSppfdsA%40mail.gmail.com.

Comments

Post a Comment

Popular posts from this blog

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

The Schaeffler and Delong diagrams for predicting ferrite levels in austenitic stainless steel welds

By Materials & Welding
Introduction Ferrite is important in avoiding hot cracking in during cooling from welding of austenitic stainless steels. 'Constitution diagrams' are used to predict ferrite levels from the composition by comparing the effects of austenite and ferrite stabilising elements. The Schaeffler and Delong diagrams are the original methods of predicting the phase balances in austenitic stainless steel welds. Nickel and chromium equivalents A 'nickel equivalent' is calculated for the austenite stabilising elements and a 'chromium equivalent' ferrite stabilising elements. These are used as the axes for the diagrams, which show the compositional equivalent areas where the phases austenite, ferrite, martensite (and mixtures of these) should be present. Although intended to show the phase balance of weld fillers, these diagrams can also be used to illustrate the phase balance of the 'parent' material. There are different diagrams for dif...
Post a Comment
Read more