Skip to main content

[MW:1465] RE: 1463] RE: 1462] Flange dimensions for size above 12" rating 2500#

By Materials & Welding
API- 6A gives dimensions of flanges upto 20000 psi

Regards

Srinivasan.R
Valdel engineers & constructors
Bangalore


-----Original Message-----
From: materials-welding@googlegroups.com
[mailto:materials-welding@googlegroups.com] On Behalf Of Somesh Kumar
Pandey
Sent: Monday, January 19, 2009 12:17 PM
To: materials-welding@googlegroups.com; piping_valves@yahoogroups.com
Subject: [MW:1463] RE: 1462] Flange dimensions for size above 12" rating
2500#


Dear Vinayak,

If you want to use the 2500# flange above 12" size, probably you need to
design the flange as non standard flange per Appendix -2 of ASME SEC
VIII Div.1 or as per the applicable code.

Regards

Somesh


-----Original Message-----
From: materials-welding@googlegroups.com
[mailto:materials-welding@googlegroups.com] On Behalf Of Nivendkar
Vinayak (Mumbai - Piping)
Sent: January 19, 2009 2:27 PM
To: materials-welding@googlegroups.com; piping_valves@yahoogroups.com
Subject: [MW:1462] Flange dimensions for size above 12" rating 2500#

Dear all,

As per ASME B 16.5 , for 2500# rating max. flange size available is upto
12". If i want to use sizes above 12" for 2500# which will be the most
appropriate standards for dimensional details.

members are requested to advice.

Regards,
Vinayak Nivendkar


This e-mail, including any attached files, may contain confidential and
privileged information for the sole use of the intended recipient. Any
review, use, distribution, or disclosure by others is strictly
prohibited. If you are not the intended recipient (or authorized to
receive information for the intended recipient), please contact the
sender by reply e-mail and delete all copies of this message.

--~--~---------~--~----~------------~-------~--~----~
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
-~----------~----~----~----~------~----~------~--~---

Comments

Post a Comment

Popular posts from this blog

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

The Schaeffler and Delong diagrams for predicting ferrite levels in austenitic stainless steel welds

By Materials & Welding
Introduction Ferrite is important in avoiding hot cracking in during cooling from welding of austenitic stainless steels. 'Constitution diagrams' are used to predict ferrite levels from the composition by comparing the effects of austenite and ferrite stabilising elements. The Schaeffler and Delong diagrams are the original methods of predicting the phase balances in austenitic stainless steel welds. Nickel and chromium equivalents A 'nickel equivalent' is calculated for the austenite stabilising elements and a 'chromium equivalent' ferrite stabilising elements. These are used as the axes for the diagrams, which show the compositional equivalent areas where the phases austenite, ferrite, martensite (and mixtures of these) should be present. Although intended to show the phase balance of weld fillers, these diagrams can also be used to illustrate the phase balance of the 'parent' material. There are different diagrams for dif...
Post a Comment
Read more