Skip to main content

Re: [MW:35910] Clarification on usage of WPS for Particular Joint Type

By Materials & Welding
The joint between the cover flange and the nozzle neck is a groove joint. However, the maximum thickness qualified in the WPS (20.0 mm) does not comply with the nozzle neck thickness requirement (20.4 mm). Therefore, this WPS is not applicable to this joint.

PWHT is an essential variable, and the approved WPS must be followed. That means if a WPS qualified with PWHT is used, PWHT shall be performed in accordance with the WPS.


 

Thanks & Best Regards,


(Mr.) Hai, Tran Ngoc

E-mail: ngochai228@gmail.com
Telephone: +84-(0)977-881-880



Vào Th 2, 15 thg 12, 2025 lúc 13:14 Shivasankar A <shivasankar2593@gmail.com> đã viết:
Hi Friends,

Refer the attached image,

In this, The cover flange thickness is 69.8 mm & The Nozzle thickness is 20.4 mm. 

the Nozzle is Set on on the Cover Flange with Full penetration Weld the groove is given on the Nozzle pipe.

The Final Fillet weld Size is 15 mm.

So may i use the WPS which Covers the thickness range from 1.5 to 20 mm?

If not, Kindly explain why?

Also Tell me the WPS Qualified with Heat treatment can be weld for the Job without Heat Treatment?

Looking for your valuable Replies. Kindly Support.

regards,
A.Shivasankar


--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion visit https://groups.google.com/d/msgid/materials-welding/6032dcdf-efef-437b-b47a-9b89a3fa83e6n%40googlegroups.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion visit https://groups.google.com/d/msgid/materials-welding/CAPmM69scSf0Q26gYvYOFQk9P6ZEhNuzOJXHqVpcLObF9r8%2Bw%3Dg%40mail.gmail.com.

Comments

Post a Comment

Popular posts from this blog

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more

Re: [MW:10788] ON PLOT PIPING & OFF PLOT PIPING

By Materials & Welding
Piping systems involved for the flow lines and gathering lines from the well head isolation valve to the production facility or processing plant isolation valve are determined as OFF PLOT. ON PLOT defines piping system in the processing plant and production platform. ANSI/ASME B31.4 applies for off plot piping system. B31.4 allows the use of either API 1104 or ASME section IX (as appropriate). However, occasionally, a very small system such as piping within 500 feet of a processing plant (some client also said 400 feet) may be declared B31.3 rather than B31.4. When B31.3 is invoked, only ASME Section IX is used. before you decide which code to use for welding procedure and/or welder qualification for pipe welding, you have to know the design and construction code applicable to the system. Please read far enough into scope and diagram illustrating the application of either B31.3 and B31.4 hope this helps rgds 2011/4/21 pradip kumar sil < pradipsil@gmail.com > Dear all, ...
Post a Comment
Read more