Materials & Welding

Please check with your GA (General Arrangement) drawing for Pig launcher what is the Code used or check your Design data sheet. Thanks & Regards J.Gerald Jayakumar On Tuesday, 31 May, 2022, 11:26:12 am GMT+4, Benaouda Mezrar <mezrarbenaouda4@gmail.com> wrote: can you please direct me in wich code i can find the acceptance criteria of NDT For Example : for piping acceptance criteria are in ASME B31.3  for pipeline acceptance criteria are in API 1104  Le mar. 31 mai 2022 à 06:35, 'james gerald' via Materials & Welding < materials-welding@googlegroups.com > a écrit : Pig launcher and Receiver design will be as per Pipeline Design code and the Closure will be as per ASME Sec.VIII Div.1 or 2. Thanks & Regards J.Gerald Jayakumar ...

Pig Traps (Launcher and Receiver) Sizing and Thicknesses and the pigging systems shall be as per Pipeline construction code.B31.4/B31.8/B31.3 upon Application. Pig Traps Fabrication as per ASME Sec.VIII Div.1 or 2. For RT requirements refer, ASME Sec.VIII Div.1 UW-51 or 52 and  for UT examination refer UW-53 . For NDT examination of ASME Sec.VIII Div.2 refer section 7.5 Thanks & Regards J.Gerald Jayakumar On Tuesday, 31 May, 2022, 11:26:12 am GMT+4, Benaouda Mezrar <mezrarbenaouda4@gmail.com> wrote: can you please direct me in wich code i can find the acceptance criteria of NDT For Example : for piping acceptance criteria are in ASME B31.3  for pipeline acceptance criteria are in API 1104  Le mar. 31 mai 2022 à 06:35, 'james gerald' via Materials & Welding < materials-we...

Pig launcher and Receiver design will be as per Pipeline Design code and the Closure will be as per ASME Sec.VIII Div.1 or 2. Thanks & Regards J.Gerald Jayakumar On Tuesday, 31 May, 2022, 07:20:40 am GMT+4, Benaouda Mezrar <mezrarbenaouda4@gmail.com> wrote: Dear experts kindly guide me in which code i can find the acceptance criteria for the construction of pig launcher and what is the desing code used (ASME B31.8 or ASME ASME-8) -- https://materials-welding.blogspot.com/ https://www.linkedin.com/groups/122787 --- You received this message because you are subscribed to the Google Groups "Materials & Welding" group. To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com . To view this discussion on t...

Dear Mezrar, It depends if Client has any Pigging Specification. In one of my project we were going to design as per B31.3 due to piping connected was also B31.3. but later we found that the Client Spec was saying about ASME Sec VIII Div. 2 hence we had to change the design code. Also the pig receiver design code has to be designed as per the connecting piping code which is by Piping. Sent from RediffmailNG on Android From: Benaouda Mezrar <mezrarbenaouda4@gmail.com> Sent: Tue, 31 May 2022 08:50:57 GMT+0530 To: Materials & Welding <materials-welding@googlegroups.com> Subject: [MW:33098] Pig launcher Dear experts kindly guide me in which code i can find the acceptance criteria for the construction of pig launcher and what is the desing code used (ASME B31.8 or ASME ASME-8) -- https://materials-welding.blogspot.com/ https://www.linkedin.com/groups/122787 --- You received this message because you are subscribed to the Google Groups "Materials & Wel...

625+304H it is better to NiCr3 or NiCr Fe2 THANKS & BEST REGARDS, KG.PANDITHAN, BE, IWE,  CSWIP 3.1, ISO 9712 Level 2 in VT, ASNT-Level II in PT,MT,RT & UT, LA ISO 9001-2015, International Welding Engineer.  CONSULTANT-WELDING & QUALITY Mobile no: +919940739349 On Fri, May 20, 2022 at 8:46 AM 'Karthik' via Materials & Welding < materials-welding@googlegroups.com > wrote: Hi, 1. Inconel 625 to SS 304H : ENiCrFe-2 or ENiCrMo-3 2. Inconel 625 to SS316L :  ENiCrFe-2 or ENiCrMo-3 Thanks& Regards, (Karthik) Karthikeyan.S M: +66-892512282 On Monday, May 16, 2022, 12:05:37 PM GMT+7, chandra sekaran < chandrasekaran.vcs@gmail.com > wrote: Dear experts kindly guide me For GTAW  1. Inconel 625 to SS 304H : what filler wire can be use  2. Inconel 625 to SS316L :  What filler wire can be u...

Hi, 1. Inconel 625 to SS 304H : ENiCrFe-2 or ENiCrMo-3 2. Inconel 625 to SS316L :  ENiCrFe-2 or ENiCrMo-3 Thanks& Regards, (Karthik) Karthikeyan.S M: +66-892512282 On Monday, May 16, 2022, 12:05:37 PM GMT+7, chandra sekaran <chandrasekaran.vcs@gmail.com> wrote: Dear experts kindly guide me For GTAW  1. Inconel 625 to SS 304H : what filler wire can be use  2. Inconel 625 to SS316L :  What filler wire can be use Regards Chandrasekaran V -- https://materials-welding.blogspot.com/ https://www.linkedin.com/groups/122787 --- You received this message because you are subscribed to the Google Groups "Materials & Welding" group. To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com . To view this d...

As per ASME Sec. VIII D1, UW8 - (d) Except when the longitudinal joints are radiographed 4 in. (100 mm) each side of each circumferential welded intersection, vessels made up of two or more courses shall have the centers of the welded longitudinal joints of adjacent courses staggered or separated by a distance of at least five times the thickness of the thicker plate. Thank you,  Regards,  S.SENTHILKUMAR On Wednesday, 18 May, 2022, 09:50:25 am IST, krishna magdum <magdumkrishna9@gmail.com> wrote: Dear team, pls suggest how much distance required for two L seam joint in pipe, some of people suggest for 4T  pls suggest for ASME Standard or code Regards  Krishna -- https://materials-welding.blogspot.com/ https://www.linkedin.com/groups/122787 --- You received this message be...

Hi There is a tendency of Cracks in Fillet weld  if Set up is not proper I. e  uneven at matching /mating  surface causing distortion There should be strong tack weld on both ends and on opposite sides Improper st up causes heavy stresses on weld causes cracks  Regards Hegde Sent from Yahoo Mail on Android On Mon, 16 May 2022 at 8:43, 'kishore barbudhe' via Materials & Welding <materials-welding@googlegroups.com> wrote: Dear expert, We observed transverse cracks after completion of fillet welding. We are using EA2 filler wire in submerge arc welding and parent materials is E 450. Please give us advice to resolve this issue. Thanks & Regards Kishore B  -- https://materials-welding.blogspot.com/ https://www.linkedin.com/groups/122787 --- You received this message because you are subscribed to the Google Groups "Materials & Welding" group. To unsubscribe from this group and stop receiving emails from it, send an ...

Dear expert, We observed transverse cracks after completion of fillet welding. We are using EA2 filler wire in submerge arc welding and parent materials is E 450. Please give us advice to resolve this issue. Thanks & Regards Kishore B 

Thanks for the reply.Its a spring loaded sandwich type NRV,so it'll be difficult for filling and draining/venting etc. On Mon, 9 May 2022 at 14:22, Lakshman Kumar < lakshmankumar4@gmail.com > wrote: Hi, If your valves are capable of holding the test pressure, no need to remove from the pipeline, Also one should not take advantage of the valves saying leakage at spindle / pinions / gaskets / etc. Further valves should not get damaged during / after testing, as it has to be in useful condition after testing also. Ensure that the valves should not partition / separate / isolate the line during testing or pressurization time, especially check valves / NRV should allow the flow during pressurization time (means pressure  pump should be on the upstream of the NRV) and also ensure to place pressure gauges at the downstream of the NRV to ensure that the line is fully pressurised  Thanks & Regards, Lakshman kumar B +91 9440031459. On Mon, 9 May 2022 at 08:53, 'Ajaykumar A'...

Hello All, I need to do hydrotest of piping systems with wafer type dual plate check valves fitted. Do they all be removed for testing? The issue I am facing is, since they are sandwiched types, there is no enough space to fit dummy spools. Kindly assist. Thanks and Regards, Ajay -- https://materials-welding.blogspot.com/ https://www.linkedin.com/groups/122787 --- You received this message because you are subscribed to the Google Groups "Materials & Welding" group. To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com . To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/546a9616-e44e-4443-897c-b70d3f01cf59n%40googlegroups.com .

On Tuesday, 5 April 2022 at 16:43:54 UTC+5:30 MW wrote: since it is 6 pass, required On Tue, 5 Apr 2022 at 16:36, 'manohar matcha' via Materials & Welding < material...@googlegroups.com > wrote: Please look into the attachment and advise that pwht is applicable for these channels as per API 660 clause 9.6.9 (a) or not? Both channels are belongs to one HE. Regards, Manohar. ClauseFrom: Raghuram Bathula < raghura...@gmail.com > Sent: Tue, 05 Apr 2022 15:37:49 To: Materials-Welding < material...@googlegroups.com > Subject: Re: [MW:33030] channels and bonnets with six or more tube passes   it is from one end of HE to another end is consider as 1 pass (not individual channel)   On Tue, 5 Apr 2022 at 15:22, 'manohar matcha' via Materials & Welding < material...@googlegroups.com > wrote: Dear Group Members, Please share your opinion/interpretation on API 660 Clause 9.6.9 (a)   Tube passes to be considered for individual channel or both ch...