Skip to main content

Re: [MW:32958] Inconel 6625 Gr1 - PQR tensile requirements

By Materials & Welding
Hi Balakriahnan, 

I do have the same concern with Gr. 1 of UNS 6625 when welded with ERNiCrMo3 Kindly do reconfirm of grade again (Gr. 1 or Gr. 2) . Did you check if the filler mamufacturer can retest the tensile properties and provide the as welded values? 785Mpa  which is 95% of 827Mpa will suffice thd requirment.  We do all weld tensile test for every batch we receive. 
I hope the expert in this forum can guidw us to sort this out. 

On Tue, Mar 8, 2022, 9:15 AM Balakrishnan Srinivasan <sbkay333@gmail.com> wrote:
Dear Experts,

Greetings for the day!!

I want to quality PQR for Base material UNS N06625 GR1 which has tensile property 827Mpa,   ERNiCrMo-3 Fillerwire was selected based on API582 & ASME sec II C recommendations. The filler wire tensile value is 760Mpa. 
In PQR tensile test result lies in between 760-827 Mpa.  The obtained tensile value is not greater than the base metal.   It can't fulfill the requirement of  QW-153 (ASME SEC IX).

As stated above clause QW153.1.c, " the applicable section".

Are there any provisions to qualify with lower strength than base metal?.

Reference WPSs were approved based on the tensile value being greater than filler metal tensile value (UTS)  760 Mpa  MIN (sec II C), But there we could not get explanations from the originators.

Please also refer, ASME-B 31.3  clause 328.3.1 (welding materials) & ASME sec VIII div1 QW-06 (non-mandatory guidelines for welding material selection.

Thank you
Balakrishnan S







--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/11e0e284-5a85-471d-a7d7-4dd57af59d0an%40googlegroups.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAKT-TupWJh4L258XN-f3bMO6YJYFVqvn6wWbjt7rPPqLCDkMgw%40mail.gmail.com.

Comments

Post a Comment

Popular posts from this blog

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

Re: [MW:10788] ON PLOT PIPING & OFF PLOT PIPING

By Materials & Welding
Piping systems involved for the flow lines and gathering lines from the well head isolation valve to the production facility or processing plant isolation valve are determined as OFF PLOT. ON PLOT defines piping system in the processing plant and production platform. ANSI/ASME B31.4 applies for off plot piping system. B31.4 allows the use of either API 1104 or ASME section IX (as appropriate). However, occasionally, a very small system such as piping within 500 feet of a processing plant (some client also said 400 feet) may be declared B31.3 rather than B31.4. When B31.3 is invoked, only ASME Section IX is used. before you decide which code to use for welding procedure and/or welder qualification for pipe welding, you have to know the design and construction code applicable to the system. Please read far enough into scope and diagram illustrating the application of either B31.3 and B31.4 hope this helps rgds 2011/4/21 pradip kumar sil < pradipsil@gmail.com > Dear all, ...
Post a Comment
Read more

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more