Re: [MW:13878] Thickness Range for Repair welding Procedure.

Thanks For Information,

But As per DEP standard - Only Partial & Cap Repair procedure required , There is no require for root opening.

Can u send me the any code which will help me regarding Material thickness range Qualifying in WPS as I mention previous Discussion.

Thanks..

On Tue, Mar 13, 2012 at 5:07 AM, Kavin Murugam <kavin202082@yahoo.com> wrote:

KINDLY FIND THE ATTCHED SKETCH FOR BETTER UNDERSTANDING.

CORRECT ME IF I'M WRONG.....

Kavin Murugam

0126159644

From: Madhu <madhusudan.rout@gmail.com>
To: Materials & Welding <materials-welding@googlegroups.com>

Sent: Monday, March 12, 2012 9:20 PM

Subject: [MW:13874] Thickness Range for Repair welding Procedure.

Dear All,

Kindly Share knowledge as details below..

I have Done Repair PQR as per ASME & DEP- SHELL DEP 31 38 01
31, Except Root opening on 12" Superduplex materil X

thickness-17.48mm.Total Deep Excavation is -13.48 mm Except Root
opening (04mm).

As per ASME Sec-IX - QW-202.3 Weld Repair and Buildup. WPS qualified
on groove welds shall be applicable for weld repairs to
groove and fillet welds.
As per DEP31 38 01 31-2.4.2 Welding of duplex stainless steel-The
quality of duplex stainless steel welds very much depends on heat-
input control. The-
3. Repair weld procedures for half wall thickness and cap repairs also
require a PQR.

Now My Query is How much thickness will Qualify In Repair WPS?

Kindly send me some Reference or Details as mention above.

Thanks & Regards

Madhusudan Rout.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

Re: [MW:34105] SA266 GR4N 4 Cycle SPWHT

Hi, You are correct, Minimum refers to the one cycle for which this part will expose until final work shop PWHT. hence mill test certificate shall include this. Max. SPWHT, refers to additional cycles of heat treatment that are reserved for future repairs during equipment lifetime. Again, these simulated no. Of cycles shall be specified in MTC. The idea is we need to make sure that steel mechanical properties are not compromised upon exposure to multiple repairs (i e 4 cycles in your case). One could say, if steel is subjected to 4 cycles and is ok, then it should by defacto be good for one cycle, yet, this is wrong assumption cause mechanical problems and microstructure of materials varies accordingly based on no. Of cycles for which material will expose. This is apparent in alloy steel and especially for impact test values as an example. In your case, this forged CS with properties before PWHT can be understood to be " as forged" condition (i.e. Wit...

Materails FAQs

Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change. Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...

Materials & Welding

Search This Blog