I also suggested the same but unfortunitly they wants documentry evidence of ASME Sec-V Artical-II..As far as Sensivity and geomentrical unsharpness i explain them but eventhouh they are not agreed unless confirm by
ASMT Section V. Sincerly request what to do for the same n how it is possible to get documentry evidence; if possible pl forward mail ID of ASMR Committee.
Wirthbest regards,
RK Vichare
----- Original Message -----
From: Sudharsan Sathianathan
To: materials-welding@googlegroups.com
Sent: Sat, 10 Sep 2011 17:13:03 +0530 (IST)
Subject: Re: [MW:12412] Measure of Sensitivity on Elliptical Joints of 2"NB pipes or any other Elliptical Radiography Shots.
Mr.Rk,
According to your attachment RIGHT SIDE SKETCH is correct .
Refer the following picture.
SSudharsan
QA/QC Manager
QA/QC Manager
Punjlloyd Oil & Gas Sdn Bhd
Malaysia
+60-105162524
Malaysia
+60-105162524
On Fri, Sep 9, 2011 at 7:08 PM, Ramchandra vichare <vicharerke@indiatimes.com> wrote:
Thanks , but my question is as per attache sketch ; pl advise.
Regards,
RK Vichare
Regards,
RK Vichare
----- Original Message -----
From: Sudharsan Sathianathan
To: materials-welding@googlegroups.com
Sent: Fri, 9 Sep 2011 14:53:58 +0530 (IST)
Subject: Re: [MW:12391] Measure of Sensitivity on Elliptical Joints of 2"NB pipes or any other Elliptical Radiography Shots.
Mr.R.KVichare,
Your thought is correct.IQI must to place on the wel,Perpendicular to the weld.
SSuharsan.--
On Fri, Sep 9, 2011 at 1:55 PM, Ramchandra vichare wrote:
MOST URGENT PL.
Dear All Experts/Experienced Personal in Process Piping in Refinery/Radiography /NDT Leverl III (RT),
Dear Friends,
As all related experince personal are know about Elliptacl Radiography shorts; my question is ; while measureing sensitivity with Wire type penetrameter whether it must be cross top & bottom image of Elliptical coverage area of weld or only top portion of weld. As per my Field experience I suggested for to cover full Elliptical coverage of weld but one of my vendor is refusing to do this same. In section 5 Artical 2 page 13 Clause(d) confirming IQI Placement for weld- Wire IQI , the IQI(s) shall be place on the weld so that the length of the ire is perpenticular to the length of the weld. I sincerely requested to all experts pl be gauide per return mail.
Mater most urgent & interesting in Radiography technology
With Best Regards,
RK Vichare
--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
--
SSudharsan
QA/QC Manager
Punjlloyd Oil & Gas Sdn Bhd
Malaysia
+60-105162524
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
--
SSudharsan
QA/QC Manager
QA/QC Manager
Punjlloyd Oil & Gas Sdn Bhd
Malaysia
+60-105162524
Malaysia
+60-105162524
--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
No comments:
Post a Comment