Re: [MW:10959] RE: 10941] SS316L PWHT

Thanks Mr. Pradip

Yes, our design code is ASME VIII Div 1. As i understood from your answer and since the two conditions indicated under UHA-44 are not rreached:

1-Design temperature (-15°C-65°C) less than 676°C as per table UHA-44

2-Strain limit is less than 10% when calculated as per cylinders fromed from plate formula

Therefore we don't need PWHT only for dish ends. Am i right???

Please confirm urgently

MOKRANI Lassaad

Project Manager

EPPM-Tunisia

lassaad.mokrani@eppm.com.tn 

00216 20 649 755

2011/5/5 pgoswami <pgoswami@quickclic.net>

Hello Mok,

MR-0175,Table A.2  specifies Environmental and materials limits for austenitic stainless steels(including S.S 316) used for any equipment or components. The requirements are:-

• be in the solution-annealed and quenched, or annealed and thermally stabilized heat-treatment condition;
• be free of cold work intended to enhance their mechanical properties; and
• have a maximum hardness of 22 HRC

NACE does not have anything mentioned on post forming strain and teat treatment.

If the design code is Sec-VIII, DIV-1, then look under table UHA-44 for "POST FABRICATION STRAIN LIMITS AND REQUIRED HEAT TREATMENT" as a function of design temperature.

I hope this would help to clear the doubts.

Thanks.

Pradip Goswami,P.Eng.IWE
Welding & Metallurgical Specialist & Consultant
Ontario,Canada.
Email-pgoswami@sympatico.ca,
pgoswami@quickclic.net

-----Original Message-----
From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of Mok
Sent: Wednesday, May 04, 2011 11:31 AM
To: Materials & Welding
Subject: [MW:10941] SS316L PWHT

Dear All,
We are fabricating two  vessels in SS316L (thickness 12mm) diameter 794mm each to be used as fuel gas separators. We have tried to convince our client that we don't need any PWHT for the shell, since the strain doesn't exceed 5% and that NACE MR0175 doesn' oblige that.
We decided to make the PWHT only for the dish ends.
But our client insisted to do it anyway for the whole vessels.
I need your input urgently

Best Regards,

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
Meilleures salutations

Mokrani Lassaad
00216 20 649 755
http://www.linkedin.com/pub/lassaad-mokrani/16/364/907


















P     Pensez environnement! N'imprimez ce mail que si c'est vraiment nécessaire
Please consider your environmental responsibility before printing this e-mail


This e-mail is confidential and it is intended only for the addressees. Any
review, dissemination, distribution, or copying of this message by persons
or entities other than the intended recipient is prohibited. If you have
received this e-mail in error, kindly notify us immediately by telephone or
e-mail and delete the message from your system. The sender does not accept
liability for any errors or omissions in the contents of this message which
may arise as a result of the e-mail transmission

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.