Tuesday, February 1, 2011

Re: [MW:9649] Re: Cr. % Variation after Heat Treatment.

Dear Israr,
                 Please check this link....      http://www.stephenson-associates-inc.com/XRF%20Basic%20Principles.pdf

2011/2/1 israr <ahmedisrar.nm@gmail.com>
Dear Harish,
Could u please give me some litratute how PMI machine work (How
electrons transmitted to material and detect elements)?

Regards
Israr Ahmed
09930308261



On Jan 31, 11:56 am, Harish Kannepalli <harishkannepa...@gmail.com>
wrote:
> Dear Israr,
>                PMI  is technique for fast identification of materials. When
> it is used for accurate measurements of chemical composition, problems
> arise. If you observe the standard deviation beside the reading, you may
> understand the reason for this variation. In XRF, the reading is given by
> the electron signal generated by the incident X-rays, so during X-ray
> irradiation the number of electrons removed may vary for each reading taken;
> the detector noise may also affect the reading. As a precaution, please use
> the PMI at max. temp of 40°C beyond which detector has more noise signal.
>
> 2011/1/31 israr ahmed <ahmedisrar...@gmail.com>
>
>
>
>
>
> > Dear All,
>
> > I had Witnessed a PMI test on Material 34CrNiMo6 The Cr. % obtain 1.3 to
> > 1.4, After Machining the Rod and Heat treatment and temparing the same
> > material is tested fore PMI and found Cr.0.98 to 1.2 Percent.The Cr. %
> > become less by 0.1 to 0.2 %. Can any body tell what may be the reason.
>
> > Regards
> > Israr Ahmed Noor Mohammed
> > +919930308261
>
> > --
> > To post to this group, send email to materials-welding@googlegroups.com
> > To unsubscribe from this group, send email to
> > materials-welding+unsubscribe@googlegroups.com<materials-welding%2Bunsubscr­ibe@googlegroups.com>
> > For more options, visit this group's bolg at
> >http://materials-welding.blogspot.com/
> > The views expressed/exchnaged in this group are members personel views and
> > meant for educational purposes only, Users must take their own decisions
> > w.r.t. applicable code/standard/contract documents.
>
> --
> regards,
> Harish.- Hide quoted text -
>
> - Show quoted text -

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.



--
regards,
Harish.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

No comments:

Re: [MW:34832] Inquiry about Single Bevel with Back Grinding

Dear Uday, As per your question that one is called with backing only,Simple both side you are welding it is backing with strip or without st...