Sunday, January 23, 2011

Re: [MW:9416] AWS Table 5.8 doubt???

As per AWS A2.4, and other than European countries, Leg size (L) is only given in drgs ( for calculation of strenght, designer will consider Throat thick as given in Codes for PWHt purpose-governing thickness)
Most European countries follow ISO 2553 where throat dimesions are being given in their drgs(a)
pandithan

On Fri, Jan 21, 2011 at 7:22 AM, r.kesav moorthi <k7moorthi@yahoo.co.in> wrote:
Both Throat & Fillet were mentioned in drawings,
throat symbol=a ,
Fillet symbol=right angle triangle.
as per drawing you have to read the requirements.
 
175, R.Kesavamoorthi,
Principal surveyor,
Quest (pvt.) Ltd.,
Ranipet.

From: krishnasamy masanam <krishnasamy1968@gmail.com>
To: materials-welding@googlegroups.com
Cc:
Sent: Thursday, 20 January 2011 8:10 PM
Subject: Re: [MW:9355] AWS Table 5.8 doubt???

Dear Friend!
                    Normally the fillet weld thickness is determined
by throat thickness, the design thickness calculated by least thick of
the base metal multiply by .0.7. and actual throat thickness
calculated by least length of the leg length multiply by 0.7 or
measured by Fillet gauge and cambridge gauge.



Have a nice day!





On 1/19/11, Srinivas Engr <srinivas.gmsrini@gmail.com> wrote:
> Dear all,
>
> AS per AWS.I knw tat for fillet weld sizes we have to refer Table 5.8.
> My doubt is they given as weld size.
> weld size refer to throat or leg length? which one tat refers?
> clear me
>
> Thanks & Regards
> Srinivas
>
> --
> To post to this group, send email to materials-welding@googlegroups.com
> To unsubscribe from this group, send email to
> materials-welding+unsubscribe@googlegroups.com
> For more options, visit this group's bolg at
> http://materials-welding.blogspot.com/
> The views expressed/exchnaged in this group are members personel views and
> meant for educational purposes only, Users must take their own decisions
> w.r.t. applicable code/standard/contract documents.
>

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.



--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

No comments:

Re: [MW:34832] Inquiry about Single Bevel with Back Grinding

Dear Uday, As per your question that one is called with backing only,Simple both side you are welding it is backing with strip or without st...