Friday, December 24, 2010

Re: [MW:8926] Problem of PWHT

On a mechanical CS line after a 0.75" valve instrumentation impulse
line is coming which is of P11 material...........welding done using
ER70S-B2L. .....and now can I do PWHT to that joint which is to b done
as per procedure of alloy steel...since this joint is between AS to CS
is there any problem in doing PWHT

On 12/24/10, Yogesh kumar <yogeshandpini@gmail.com> wrote:
> Hi vivek
>
> Will you please elaborate more your CS/AS joint configuration is not
> getting clear to me??
> yogesh.
>
>
> On Fri, Dec 24, 2010 at 9:25 AM, vivek m <vivekmohan007@gmail.com> wrote:
>
>> The impulse line is of P11 material and it has to be post heated...i
>> want to knw d problems dat may occur to the 0.75 joint between cs and
>> as
>>
>> On 12/23/10, Bathula Raghuram (Mumbai - PIPING) <R.Bathula@ticb.com>
>> wrote:
>> > Generally Impulse lines are outside scope of ASME B31.3 and don't
>> > require
>> > PWHT. Even if it is designed by B31.3 it doesn't require PWHT as
>> thicknesses
>> > low, , unless it is a contractual requirement
>> >
>> > -----Original Message-----
>> > From: materials-welding@googlegroups.com
>> > [mailto:materials-welding@googlegroups.com] On Behalf Of vivek m
>> > Sent: Thursday, December 23, 2010 9:34 PM
>> > To: materials-welding@googlegroups.com
>> > Subject: [MW:8914] Problem of PWHT
>> >
>> > Dear all,
>> > one of my P11 impulse pipe (0.75") is connected to a CS 0.75" valve
>> > which comes with big bore CS line (all as per drawing)......now shall
>> > i do pwht to that joint ? If done will there be any problem to that
>> > joint ...please give me a detailed answer.
>> >
>> >
>> > Filtered by Hosted Filtering
>> >
>> >
>> > --
>> > To post to this group, send email to materials-welding@googlegroups.com
>> > To unsubscribe from this group, send email to
>> > materials-welding+unsubscribe@googlegroups.com<materials-welding%2Bunsubscribe@googlegroups.com>
>> > For more options, visit this group's bolg at
>> > http://materials-welding.blogspot.com/
>> > The views expressed/exchnaged in this group are members personel views
>> and
>> > meant for educational purposes only, Users must take their own decisions
>> > w.r.t. applicable code/standard/contract documents.
>> >
>>
>> --
>> To post to this group, send email to materials-welding@googlegroups.com
>> To unsubscribe from this group, send email to
>> materials-welding+unsubscribe@googlegroups.com<materials-welding%2Bunsubscribe@googlegroups.com>
>> For more options, visit this group's bolg at
>> http://materials-welding.blogspot.com/
>> The views expressed/exchnaged in this group are members personel views and
>> meant for educational purposes only, Users must take their own decisions
>> w.r.t. applicable code/standard/contract documents.
>>
>
> --
> To post to this group, send email to materials-welding@googlegroups.com
> To unsubscribe from this group, send email to
> materials-welding+unsubscribe@googlegroups.com
> For more options, visit this group's bolg at
> http://materials-welding.blogspot.com/
> The views expressed/exchnaged in this group are members personel views and
> meant for educational purposes only, Users must take their own decisions
> w.r.t. applicable code/standard/contract documents.
>

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

No comments:

Re: [MW:34832] Inquiry about Single Bevel with Back Grinding

Dear Uday, As per your question that one is called with backing only,Simple both side you are welding it is backing with strip or without st...