Skip to main content

Re: [MW:8096] (NAS144M) equivalent of this material??

By Materials & Welding
Hi i have found some info for you from net.
 
I understand this high alloy stainless steel. This is not typical 316 L, because, please not Moly content 6.0 to 6.5, Hope this will help you, but you have to search for Standard for 254 MSO
 
Thanks
 
Murugesan
 
 
 
 
 
254SMO
Chemical Composition %
C Cr Cu Mn Mo N Ni P Si S
Max     Max       Max Max Max
0.02 19.5-20.5 0.5-1.0 1.0 6.0-6.5 0.18-0.22 17.5-18.5 0.03 0.80 1.01

AVAILABILITY
Weld Pipe 3/4"- 12"
Butt-Weld Fittings 3/4" - 12"
Flanges 3/4" - 12"
Bar 1" - 8"
SPECIFICATIONS
ASTM A312, A403, A182
ASME SA312, SA403, SA182

DESCRIPTION
254SMO is an austenitic stainless steel designed for maximum resistance to pitting and crevice corrosion. With high levels of chromium, molybdenum, and nitrogen, 254SMO is especially suited for high chloride environments such as brackish water seawater pulp mill bleach plants and other high chloride process streams. 254SMO offers chloride resistance superior to that of Alloy 904L Alloy 20, Alloy 825 and Alloy G. 254SMO is compatible with the common austenitic stainless steels. It is often used as a replacement in critical components of larger constructions where Type 316L or 317L has failed by pitting, crevice attack, or chloride stress corrosion cracking. In new construction, 254SMO has been found in many cases to be a technically adequate and much less costly substitute for nickelbased alloys and titanium. 254SMO is substantially stronger than the common austenitic grades, but is also characterized by high ductility and impact strength. 254SMO is readily fabricated and welded.
(R) 254SMO is A REGISTERED TRADEMARK OF AVESTA SHEFFIELD

DESIGN FEATURES
High resistance to pitting, crevice and general corrosion.
Very high resistance to chloride stress corrosion cracking.
50% stronger than 300-series austenitic stainless steels.
Excellent impact toughness.
Excellent workability and weldability

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding+unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

Comments

Post a Comment

Popular posts from this blog

Re: [MW:34105] SA266 GR4N 4 Cycle SPWHT

By Materials & Welding
Hi,  You are correct, Minimum refers to the one cycle for which this part will expose until final work shop PWHT. hence mill test certificate shall include this.  Max. SPWHT, refers to additional cycles of heat treatment that are reserved for future repairs during equipment lifetime.  Again, these simulated no. Of cycles shall be specified in MTC.  The idea is we need to make sure that steel mechanical properties are not compromised upon exposure to multiple repairs (i e 4 cycles in your case).  One could say, if steel is subjected to 4 cycles and is ok, then it should by defacto be good for one cycle, yet, this is wrong assumption cause mechanical problems and microstructure of materials varies accordingly based on no. Of cycles for which material will expose. This is apparent in alloy steel and especially for impact test values as an example.  In your case, this forged CS with properties before PWHT can be understood to be " as forged" condition (i.e. Wit...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more