Tuesday, September 21, 2010

Re: Re: [MW:7124] selection criteria for root, face and side bend test

Dear Muthu Barathi Sir,
 
Could you please mention that particular clause from ASME B31.3 and AWSD1.1 regarding bend test selection criteria?
 
Regards,
 
Limesh

On Mon, Sep 20, 2010 at 10:57 PM, muthu barathi <muthu_barathi@rediffmail.com> wrote:
Hi,

It depends upon thickness . up to half inch root bend, face bend, and
tensile, bend test. beyond half inch thk side bend,and tensile . you
can refer individual codes as AWS D1.1, Piping ASME B 31.1 and SEC IX
too


Muthu Barathi P

Sr Manager QA/ QC

On Tue, 21 Sep 2010 08:52:19 +0530 wrote

>Dear Mr. Limesh,                          Criteria is plate/pipe
thickness. If the thickness is greater than or equal to 10mm then go
for side bend, thickness less than10mm u have to go for face/root. As
said by Mr. Karthick refer QW 451.1 in ASME sec IX.


2010/9/20 limesh M

Dear All,
I found that some specimen tested by root and face bend.Some specimen
tested by side bend only.
What is the selection criteria for root, face and side bend test?
Is there any clause in ASME BPV SEC IX regarding this?
 
Regards,
 
Limesh



--

To post to this group, send email to materials-welding@googlegroups.com

To unsubscribe from this group, send email to materials-welding-
unsubscribe@googlegroups.com

For more options, visit this group's bolg at http://materials-
welding.blogspot.com/

The views expressed/exchnaged in this group are members personel views
and meant for educational purposes only, Users must take their own
decisions w.r.t. applicable code/standard/contract documents.



--
regards,
Harish.





--
>
To post to this group, send email to materials-welding@googlegroups.com
>
To unsubscribe from this group, send email to materials-welding-
unsubscribe@googlegroups.com
>
For more options, visit this group's bolg at http://materials-
welding.blogspot.com/
>
The views expressed/exchnaged in this group are members personel views
and meant for educational purposes only, Users must take their own
decisions w.r.t. applicable code/standard/contract documents.
>


Dear Sir,





Thanking You,

Honesty is the best Policy

With Warm Regards,

P Muthu Barathi
Mobile No:09967300544

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

No comments:

[MW:34820] RE: 34813] Clarification in Rate of heating and cooling.

Hello,   Please see the response below.   Regards.   P. Goswami, P. Eng, IWE.   From: materials-welding@googlegroups.com <materials-weld...