Wednesday, September 15, 2010

Re: [MW:7017] RE: 6999] ASME SEC IX Code Issue

Dear All,
Sorry for my mistake in Interpretation and suggestion on this quiery.
 
According to Mr.John,he was correct with QW406.3.
 
Thanks & regards,
 
(karthik)

Karthikeyan.S
QA/QC Manager
Getabec Energy Co.,Ltd.
379,Moo6,Soi8,Nikhomphatana,
Rayong-21180,
Thailand.
Phone: 0066 38 897035-8 (Off)
Fax: 0066 38 897034
Hand Phone: 0066 892512282


--- On Wed, 9/15/10, limesh M <limesh78@gmail.com> wrote:

From: limesh M <limesh78@gmail.com>
Subject: Re: [MW:7015] RE: 6999] ASME SEC IX Code Issue
To: materials-welding@googlegroups.com
Date: Wednesday, September 15, 2010, 10:59 AM

Dear Karthik Sir,
 
My query was based on ASME SEC IX QW 406.3,I think you mistakenly taken it as QW 403.6
 
Regards,
 
Limesh

On Tue, Sep 14, 2010 at 9:15 PM, Karthik <karthik6684@yahoo.com> wrote:
Hi,
I dont find where is the interpass temp.and all in QW403.6?
 
Pls.Find below the Extraction from ASME Sec.IX-2007
 

QW-403.6 The minimum base metal thickness qualified

is the thickness of the test coupon T or 58 in. (16 mm),

whichever is less. However, where T is less than 14 in.

(6 mm), the minimum thickness qualified is 12T. This limitation

does not apply when a WPS is qualified with a PWHT

above the upper transformation temperature or when an

austenitic material is solution annealed after welding.
 
Regarding Interpass Temp.Pls.find below the extraction from code.
 

QW-406.8

An increase in the maximum interpass temperature

of more than 100°F (56°C) from that achieved on

the test coupon and recorded on the PQR. The interpass

temperature shall be measured and recorded separately for

each tempering weld bead layer and, if any, for the surface

weld bead layer(s). The WPS shall specify the maximum

interpass temperature limits for each tempering bead layer

separately and for the surfacing weld bead layer(s), if any.
 
Hi limesh,
As he pointed out for interpass temp.your wps shall be with interpass temp 140+56 =196
 
Thanks & Regards,
 
(Karthik)

Karthikeyan.S
QA/QC Manager
Getabec Energy Co.,Ltd.
379,Moo6,Soi8,Nikhomphatana,
Rayong-21180,
Thailand.
Phone: 0066 38 897035-8 (Off)
Fax: 0066 38 897034
Hand Phone: 0066 892512282


--- On Tue, 9/14/10, John Henning <jhenning@deltak.com> wrote:

From: John Henning <jhenning@deltak.com>
Subject: [MW:7004] RE: 6999] ASME SEC IX Code Issue Date: Tuesday, September 14, 2010, 9:48 PM


No  - Per QW-406.3 WPS maximum permitted is PQR value + 55C.  Therefore WPS IP max = 140C + 55C  =  195C
 
From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of limesh M
Sent: Tuesday, September 14, 2010 7:43 AM
To: materials-welding@googlegroups.com
Subject: [MW:6999] ASME SEC IX Code Issue
 

Dear All,

Design Code: ASME B31.3     Welding Code: ASME SEC IX

I have a Low temperature carbon steel impact tested PQR with a PWHT range of 600⁰±10⁰C.Is this condition giving an exemption for me on QW406.3 to prepare a WPS with maximum interpass temperature of 200⁰C.

Maximum interpass temperature observed during specimen welding: 140⁰C

 
Regards,
 
Limesh
--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

No comments:

[MW:34820] RE: 34813] Clarification in Rate of heating and cooling.

Hello,   Please see the response below.   Regards.   P. Goswami, P. Eng, IWE.   From: materials-welding@googlegroups.com <materials-weld...