Monday, June 7, 2010

Bls: Re: [MW:5425] storage condition of E6013

Hello,

It is true that Rutile (Ti02) Electrode does not require baking, because it is meant to have an amount of moisture inside to achieve better deposition rate, usually required for pipeline welding. If you bake, the moisture will be gone and the required effect will not be achieved.

Tq & Regards
Omar

Dari: sugu puma <pumamy@yahoo.com>
Kepada: materials-welding@googlegroups.com
Terkirim: Ming, 6 Juni, 2010 21:21:43
Judul: Re: Re: [MW:5416] storage condition of E6013


are they sure you said cannot baking in oven..............?,what the manufacture recommendation said?

From: john rodrigues <johnrodrigues2@rediffmail.com>
To: materials-welding@googlegroups.com
Sent: Sun, June 6, 2010 3:39:15 PM
Subject: Re: Re: [MW:5412] storage condition of E6013

Hello,
E6013 is rutile type electrode and it does not require baking.
Regards.
joh

On Sun, 06 Jun 2010 09:09:34 +0530 wrote
>Dear all,
The baking temperature is 350 - holding temperature 150,see the manufacture rules and regulations before open the box of electrode cartoon,this is all low hydrogen electrode using,followup according manufacture recommendation and also take look in AWS D1.1.

From,
M.Sugumar


From: Sandeep Kp
To: materials-welding@googlegroups.com
Sent: Sat, June 5, 2010 10:34:30 PM
Subject: [MW:5401] storage condition of E6013


Dear all,
Let me know the baking & holding temperature of E6013 electrodes of ESAB.


Regds,

Sandeep.k.p







--

To post to this group, send email to materials-welding@googlegroups.com

To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com

For more options, visit this group's bolg at http://materials-welding.blogspot.com/

The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.









--
>
To post to this group, send email to materials-welding@googlegroups.com
>
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
>
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
>
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
>



John Rodrigues

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

--
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.

No comments:

Re: [MW:34832] Inquiry about Single Bevel with Back Grinding

Dear Uday, As per your question that one is called with backing only,Simple both side you are welding it is backing with strip or without st...