Skip to main content

[MW:2964] Re: Rolling machine Rolls repair

By Materials & Welding
Dear Prem Nautiyal
i don't have relatedexprience .but i suggest you must have a ductile material in core(inner surface ) and a  hard material in surface.therefore to achieve it ,first you make  holes in both starting and ending of crack, then remove and groove that area.
use from low hydrogen electrodes (basic type) such as 9018 or 10018.during welding the temperature of preheat not be lower than  150 or 200.before compeletion of weld(5-7 mm lower of base metal surface) use from hard surfacing electrodes.
do you have equipment for heat treating of rolling.
regards.

On Mon, Aug 17, 2009 at 8:00 AM, PREM SHANKARDUTT NAUTIYAL <prem_nautiyal@rediffmail.com> wrote:
Dear Friends

We have a Four Roll Plate Rolling Machine in our Fabrication shop. We had purchased this machine from Italy a couple of years ago.
Now we have observed some cracks on two rollers of length @100mm. The depth is @28mm,confirmed by UT.
We have also done spectro-chemical analysis of the roller by a portable spectro. The results are:
C=0.45, Si=0.29, Mn=0.81, Cr=0.1, Mo=0.03, Ni=0.14, Fe=97.14, S=0.002, P=0.003
Hardness= 53-55HRC (checked by portable hardness tester on surface).
Since the supplier / manufacturer of this Rolling Machine is not responding to us we have decided to repair these 2 rollers on our own inhouse.
Does any one have such experience in the past.
What would be the correct electrode, preheat,interpass, postheat,PWHT, welding precautions ?
We have dismantled these two rollers and are ready for repair.
Expert suggestions are welcome..

Regards

Prem Nautiyal



PREM S NAUTIYAL
CELL : 9820313278
--~--~---------~--~----~------------~-------~--~----~
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
-~----------~----~----~----~------~----~------~--~---

Comments

Post a Comment

Popular posts from this blog

Re: [MW:34105] SA266 GR4N 4 Cycle SPWHT

By Materials & Welding
Hi,  You are correct, Minimum refers to the one cycle for which this part will expose until final work shop PWHT. hence mill test certificate shall include this.  Max. SPWHT, refers to additional cycles of heat treatment that are reserved for future repairs during equipment lifetime.  Again, these simulated no. Of cycles shall be specified in MTC.  The idea is we need to make sure that steel mechanical properties are not compromised upon exposure to multiple repairs (i e 4 cycles in your case).  One could say, if steel is subjected to 4 cycles and is ok, then it should by defacto be good for one cycle, yet, this is wrong assumption cause mechanical problems and microstructure of materials varies accordingly based on no. Of cycles for which material will expose. This is apparent in alloy steel and especially for impact test values as an example.  In your case, this forged CS with properties before PWHT can be understood to be " as forged" condition (i.e. Wit...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more