Skip to main content

[MW:1932] RE: 1929] Welding L7M Nuts on P1 material

By Materials & Welding

This is the case of welding P no  (Asigned ) to Non assigned No ,We can weld by compatible welding consumable with WPS qualified accordingly as per ASME sec IX  However that will be case to case basis.

 

From: materials-welding@googlegroups.com [mailto:materials-welding@googlegroups.com] On Behalf Of Bathula Raghuram (Mumbai - PIPING)
Sent: Monday, April 13, 2009 9:53 AM
To: materials-welding@googlegroups.com
Subject: [MW:1929] Welding L7M Nuts on P1 material

 

Probably the best way is to qualify a fillet weld procedure using these nuts.

 

Hegde P.B.

 

Non mandatory Precautions:

- when we have to weld the bolts (especially the nuts) we have to consider that these materials usually have larger percentages of Pb, Sulphur, Phosphorous and Carbon and then their welding is critical;

- as per above, covered electrodes (instead of GTAW) with low strength level have to be preferred;

- careful cleaning by degreasing is mandatory;

- preheating could be useful to decrease the cooling rate.

 

From: -----------------------------------
Sent: Sunday, April 12, 2009 12:26 PM
To: Bathula Raghuram (Mumbai - PIPING)
Subject: Welding L7M Nuts

 

There is a situation of welding of SA 194 L7M nuts is to SA 516 Gr-70 plate. Since there is no P number assigned for SA 194 L7M (another UNS number is availalbe), theorotically we can not use the existing P number-1 WPS/PQR.

 

In my opinion considering the practical situation, since SA 194 L7M is compatible with SA 516 Gr-70 considering the mechanical properties, design & service requirements (since going into the same equipment), weldability, we can  use P1 WPS/PQR??

 

To establish WPS/PQR (just to meet the section-IX requirements), then what option is available (weld the raw material bar ?) ??

 

regards

GH  

 


 


--~--~---------~--~----~------------~-------~--~----~
To post to this group, send email to materials-welding@googlegroups.com
To unsubscribe from this group, send email to materials-welding-unsubscribe@googlegroups.com
For more options, visit this group's bolg at http://materials-welding.blogspot.com/
The views expressed/exchnaged in this group are members personel views and meant for educational purposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
-~----------~----~----~----~------~----~------~--~---

Comments

Post a Comment

Popular posts from this blog

Re: [MW:34105] SA266 GR4N 4 Cycle SPWHT

By Materials & Welding
Hi,  You are correct, Minimum refers to the one cycle for which this part will expose until final work shop PWHT. hence mill test certificate shall include this.  Max. SPWHT, refers to additional cycles of heat treatment that are reserved for future repairs during equipment lifetime.  Again, these simulated no. Of cycles shall be specified in MTC.  The idea is we need to make sure that steel mechanical properties are not compromised upon exposure to multiple repairs (i e 4 cycles in your case).  One could say, if steel is subjected to 4 cycles and is ok, then it should by defacto be good for one cycle, yet, this is wrong assumption cause mechanical problems and microstructure of materials varies accordingly based on no. Of cycles for which material will expose. This is apparent in alloy steel and especially for impact test values as an example.  In your case, this forged CS with properties before PWHT can be understood to be " as forged" condition (i.e. Wit...
Post a Comment
Read more

Materails FAQs

By Materials & Welding
Q: What are equivalents for standard Q 235 B (and Q 235 A) for U-channels? (asked by: boris.vielhaber@vait.com) A: DIN Nr. = 2393 T.2, 2394 T.2, EN 10025 W. Nr. DIN 17007 = 1.0038 Design DIN 17006 = RSt 37-2, S235JRG2 (Fe 360 B) Q: What is St DIN 2391 BK material? (asked by: dmcandrews@automaticstamp.com) A: Precision steel tubes, cold-finished/hard. Q: What is C.D.W. Boiler Tube? (asked by: montydude123@yahoo.com) A: Cold Drawn Welded Boiler Tube. Q: WHAT IS W.Nr. 1.4301? PLS TELL US IN EASY LANGUAGUE (asked...
21 comments
Read more

Heat tint (temper) colours on stainless steel surfaces heated in air // Heat tint

By Materials & Welding
Introduction The colour formed when stainless steel is heated, either in a furnace application or in the heat affected zone of welds, is dependent on several factors that are related to the oxidation resistance of the steel. The heat tint or temper colour formed is caused by the progressive thickening of the surface oxide layer and so, as temperature is increased, the colours change.   Oxidation resistance of stainless steels However, there are several factors that affect the degree of colour change and so there is no a single table of colour and temperature that represents all cases. The colours formed can only be used as an indication of the temperature to which the steel has been heated. Factors affecting the heat tint colours formed Steel composition The chromium content is the most important single factor affecting oxidation resistance. The higher the chromium, the more heat resistant the steel and so the development of the heat tint colou...
Post a Comment
Read more